John Deere 550 Round Baler

products_image_2products_image_3products_image_4
 
Great condition, wide pickup (1.81mtr). Netwrap system. Used this season, sold due to retirement.
£2,150+VAT

2001 Ifor Williams HB510 Horse Box

products_image_2products_image_3products_image_4
 
In blue, with centre partition and front and rear breech bars. For two horses up to  17.2hh. Front and rear ramps & jockey door. All lights in working order. Recently serviced, with new tyres fitted.
£3,200 NO VAT

Predator King Pro Paddock Vacuum

products_image_2products_image_3products_image_4
 
It's a poop sucker, basically. Electric start, Briggs & Stratton 13Hp Commercial Performance engine. Comes with 2 different length suction hoses. UK built. New fuel tank and battery just fitted by us.
£1,200+VAT

John Deere 1445 Series 2 Mower

products_image_2products_image_3products_image_4
 
4WD, diesel out-front mower. 2,360hrs, road registered. With Fastback commercial 62" deck, very tidy condition.
£4,950+VAT
 

John Deere 1565 Series 2 Mower

products_image_2products_image_3products_image_4
 
2010, 4WD with 1,300 hours. Road registered. '7 Iron II' Commercial 72" deck and MCS600 PLUS high-tip collector. Lovely bit of kit.
£8,950+VAT

Kubota B2410 4WD Compact Tractor

products_image_2products_image_3products_image_4
 
740 hours, hydrostatic drive, grass tyres. Mid-mounted 5ft deck, roll bar and power steering. Linkage mounted collector, front weights.
£7,950+VAT

John Deere 2WD Gator

products_image_2products_image_3products_image_4
 
2000 model, road registered and running, but needs a little bit of tidying.
£1,200+VAT

Used Ifor Williams GD106

products_image_2products_image_3products_image_4
 
10ft x 5' 7" general duty trailer. Full width, drop down mesh ramp. Twin axle. Bed is in decent condition, tyres are OK. Electrics need attention.
£850+VAT
 

Used Indespension 16ft Tilt Bed Trailer

products_image_2products_image_3products_image_4
 
16ft x 6ft 6" bed. Manual tilt, with 2ft full width, mesh, drop-down, tail ramp for easy loading. No headboard or sides. Twin axle. Overall good condition.
£1,600+VAT

Used Indespension 16ft Trailer

products_image_2products_image_3products_image_4
 
16ft x 6ft 6" bed. Twin axle, with 6ft, full width, sprung-loaded, mesh ramp. With headboard. Seen a lot of use, but fairly tidy overall.
£1,475+VAT

2002 Kubota L4200 4WD

products_image_2products_image_3products_image_4
 
On turf tyres. With cab, power steering, two double spools & 3-point linkage. Showing only 1,378 hours. Creeper & shuttle gearbox.
£7,950+VAT

2006 Marshall S4 Tipping Trailer

products_image_2products_image_3products_image_4
 
10ftx6ft bed, 4 ton capacity, with 18" dropsides and standard tailgate. Fitted with extended 18" mesh sides. Hydraulically braked and road lights.
£1,950+VAT
 

2011 A S Marston Tipping Trailer

products_image_2products_image_3products_image_4
 
2.8mtr x  1.9mtr bed, 4 ton capacity. With 18" dropsides. Very clean and tidy. Getting hard to find decent second hand trailers of this size, so grab it quick!
£1,750+VAT

24″ Auger Bit

products_image_2products_image_3
 
24" (2ft) heavy duty auger for post hole borer. To suit 2 1/2" shaft size.
£100+VAT

6″ Auger Bit

products_image_2products_image_3
 
6" heavy duty auger bit for post hole borer. To suit 2 1/2" shaft diameter.
£100+VAT

Weeks 4 Ton Tipping Trailer

products_image_2products_image_3products_image_4
 
1978. Made for Massey Ferguson by Weeks Trailers Ltd. Drop sides. Slight leak on the ram when tipping. Rot in places, needs attention (hence price). High mesh sides.
£375+VAT
 

Cotesi Hay Twine 10,000 ft

 
Conventional baler hay twine now in stock! Colour: Rust, 10,000ft (per 2-spool pack), 100% polypropylene with anti-UV and knot-free. Please contact for details.

Sisal 8,000ft Baler Twine

products_image_2
 
Sisal conventional baler twine now in stock! With rot and rodent protection. Please contact for details.

Nuffield Front Weight

products_image_2products_image_3
 
In good order, and becoming increasingly hard to find (figuratively speaking, not literally, unless you have very long nettles...)
£225+VAT

International Front Tractor Weights

products_image_2products_image_3
 
Pair of front, under-slung nose weights. To suit I-H tractors, recently removed from a 434 (pictures illustrate how they fit, tractor is not included!)
£195+VAT
 

Ford Tractor Weights

products_image_2
 
Set of 9 wafer weights for Ford.
£250+VAT

Set Of Massey Ferguson Weights

products_image_2products_image_3products_image_4
 
MF100 series. Set of 8 comprising 2 x starter rings & 6 x bolt-ons. Requires 4 x bolts (spaced 16-1/2" apart). Marked with MF number 899164M1
£395+VAT

Tractor Loader Counterweight

products_image_2products_image_3
 
3 point linkage mounted tractor loader counterweight.
£95+VAT

Massey Ferguson Rear Tractor Weight

products_image_2products_image_3
 
Rear ballast weight for use with MF T-bar. Ideal when using loader, as it helps with both traction and steering.
£120+VAT
 

Rear Weight For Loader Tractor

products_image_2products_image_3products_image_4
 
Complete with stand and quick hitch bracket.

Fordson Major Wheel Weight Set

products_image_2products_image_3products_image_4
 
To suit Major, Power Major & Super Major. Set of six rings (two inner mounting rings, and four outer weight rings). Later type, marked with 'Enfo' not 'E27N'. No fixings supplied with these weights.
£450+VAT

Pair Front Wheel Weights

products_image_2products_image_3
 
600x16/750x16 standard weights. Fits most 2WD model tractors. Complete with 4 bolts per weight. 7-1/2" - 19cm centres.
£195+VAT

Ford Rear Wheel Weights (Set Of 6)

products_image_2
 
Fits Ford 4000-10 series wheels.
£275+VAT
 

New Pair Goodyear Rear Tyres 11×28

products_image_2products_image_3products_image_4
 
Genuine Goodyear 12.4-28 (11 x 28's) rear tyres. Price for pair. These are new tyres, never fitted.
£550 inc VAT

New Full Set (4) Goodyear Tyres

products_image_2products_image_3products_image_4
 
Genuine Goodyear tyres. Full set 12.4-28 (11 x 28) rears and 600 x 16 fronts. These are brand new, never fitted tyres.
£800 inc VAT

Spade Lug Rear Wheels

products_image_2products_image_3
 
Original spade lug wheels, designed for Ferguson T20 tractors. Will also fit MF35/135 and Fordson Dexta.

Standen Row Crop Wheels

products_image_2products_image_3products_image_4
 
8.3R44 to fit Ford 8 stud tractors (such as 4000, 5000, 4610, 6610 etc)
£350+VAT
 

Used Ifor Williams GD125 With Mesh Sides

products_image_2products_image_3products_image_4
 
12x5, with drop down tail gate. Lights not working (trailer board fitted in place).

1988 Benford 4000 Dumper

products_image_2products_image_3products_image_4
 
4WD, pivot steer with ROPS. Electric start, Lister-Petter 3 cylinder engine. Manual gears, one owner from new. Tidy.
£3,250+VAT

Horse Box Day Hire

products_image_2products_image_3products_image_4
 
Day hire of a horse box is available by prior arrangement. £50 + VAT per day. Weekend hire (collect Friday, return Monday) only £120 + VAT

Ifor Williams HB506 Graphite Horse Box

products_image_2products_image_3products_image_4
 
Suitable for two horses up to 16.2hh. Centre partition and front & rear breeching bars as standard. Twin axle. Grooms door, front and rear offload ramps. Sliding side windows. Used once for demonstration.
 

Thwaites 7000 Dumper

products_image_2products_image_3products_image_4
 
4WD, pivot steer dumper with ROPS. Very straight and tidy machine. Well maintained over the years.
£3,950+VAT

Ferguson Continental Rear Wheels with Solid Centres

products_image_2
 
£195+VAT

Pair Goodyear 11.2-10×28 Wheel & Tyres

products_image_2products_image_3products_image_4
 
Diamond pattern, originally fitted on Ferguson Continental. 10x28, solid centre, early Ferguson rims.

Wells Mark V Stone Cropper

products_image_2products_image_3products_image_4
 
Suitable for stone up to 600mm (24") wide and up to 250mm (10") deep. Requires hydraulic operation (either from power pack or from tractor/digger flow & return). Independent suspension units with positionable wheels to allow for towing on a 50mm ball hitch.
£1,750+VAT
 

Pair 11.2-10×28 Wheels With Grass Tyres

products_image_2products_image_3products_image_4
 
Rims are tatty with well worn tyres, hence price.
£160+VAT

David Brown Wheels & Tyres

products_image_2products_image_3
 
11 x 36 David Brown wheels & tyres.
£250+VAT

Pair 12.4R32 Massey Ferguson Wheels

products_image_2products_image_3products_image_4
 
To suit MF148, 550 etc. With good Michelin radials (around 90%).

Massey Ferguson Drill Wheels (Pair)

products_image_2products_image_3products_image_4
 
Will also suit 35/135 as row-crop wheels. 600-36 tyres (seen better days, but serviceable) One tyre has a rather bad patch appearing (see photo). Priced as pair.
£200+VAT
 

Oxdale 8ft Weeder Tine

products_image_2products_image_3products_image_4
 
3-point linkage mounted grass harrow weeder tine. 8mm tines. Removes moss, dead grass and other grassland weeds. Other sizes available to order.
£520+VAT

Oxdale Compact Tractor Towbar

products_image_2products_image_3
 
3 point linkage mounted towbar. Ideal for moving trailers, caravans or anything with a standard ball-hitch drawbar with no fuss. Small version for compact tractors.
£95 inc VAT

1973 County 4000-Four

products_image_2products_image_3products_image_4
 
Good tyres, very tidy all round. Recent engine rebuild with new clutch, pressure plate and spigot bearing. New oil seals to front of gearbox. Comes with pick up hitch (currently not fitted) and flat draw bar. Being sold on behalf of customer. Not on site at Langley Farm, so please contact the office and we will put the owner in touch with you regarding viewings etc. Private sale, no VAT.
£9,000 no VAT

Massey Loader & Fork To Fit MF35-135

products_image_2products_image_3products_image_4
 
Complete with front grill guard/stand combination, muck-fork, all pipe-work, bolts, pins etc. Removed from MF35.
£395+VAT
 

MF Loader For 675 Tractor

products_image_2products_image_3products_image_4
 
Recently removed from MF675 2WD tractor. With brackets and pipework, but no attachment supplied.

Quicke 2560 Loader

products_image_2products_image_3products_image_4
 
Complete with MF bracket and spool block. Recently removed form 575 tractor, will also fit 590 etc.
£600+VAT

Quicke 3260 Loader

products_image_2products_image_3products_image_4
 
Removed from MF590, complete with quick-release muck fork. With 3-spool valve, pipework and brackets etc.
£750+VAT

David Thomas Roll Bar – A

products_image_2products_image_3
 
Square section, 'lift out' type. Suits Fordson Dexta/Super Dexta, Ford 2000-3000, Ferguson T20's, MF 35-135 etc. Please quote 'roll bar A' in all enquiries.
£195+VAT
 

Titan Tubular Roll Bar – B

products_image_2products_image_3
 
To suit MF35-135, Fordson Dexta/Super Dexta, Ford 2000-3000 etc. Please quote 'roll bar B' in all enquiries.

Flatford Roll Bar – C

products_image_2products_image_3products_image_4
 
Square fixed style roll bar. To suit Ferguson T20's, MF35-135 etc, Fordson Dexta/Super Dexta, Ford 2000-3000 etc. Please quote 'roll bar C' in all enquiries.
£120+VAT

David Thomas Roll Bar – E

products_image_2products_image_3products_image_4
 
Square-section, non-folding type. To suit Ferguson T20's, MF35-135, Fordson Dexta/Super Dexta, Ford 2-3000 etc. Please quote 'roll bar E' in all enquiries.
£195+VAT

International Harvester Roll Bar – M

products_image_2products_image_3products_image_4
 
Square-section, fold down type. To suit I-H 250, 275, 414 etc. Please quote 'roll bar M' in all enquiries.
 

Mitsubishi L200 GL 4Work Club Cab Pickup

products_image_2products_image_3products_image_4
 
MOT til August. Dark blue, 2004 model with 2.5 diesel engine & tow bar. Good, working motor. Needs a clean. 94,000 miles.
£3,700+VAT

2010 Toyota Hi-Lux HL2 Pick Up

products_image_2products_image_3products_image_4
 
Double cab, 55,000 miles with full service history. 2 owners, very clean and tidy pick-up. More pictures available on request.

2013 Land Rover Defender Pick Up

products_image_2products_image_3products_image_4
 
SWB, 20,000 miles. Still under manufacturers warranty. Owned and operated by us from new. Just been serviced by local dealer.
£14,500+VAT

Kawasaki KLF300 Quad Bike

products_image_2products_image_3products_image_4
 
Dual mode differential, 4,790hrs. Semi-automatic gear change (gear change through pedal but no clutch lever). 5 forward, 1 reverse. Electric start. Tow ball. Road registered as agricultural vehicle, but no V5 document.
 

2008 Suzuki 400AS 4×4 Kingquad

products_image_2products_image_3products_image_4
 
Suzuki LT-A400/F. Only 333hrs from new. Starts and runs well. With operators manual, handle bar mitts, front and rear racks and rear tow-ball. No road legal kit, and therefore obviously not road registered.

Complete MF Pick Up Hitch Assembly

products_image_2products_image_3products_image_4
 
Removed from MF550, but will also fit MF35 or 135 etc. This is the later type with rod style pick up bars. Complete unit with fixings.
£550+VAT

2007 Kubota U45-3 4.5T Excavator

products_image_2products_image_3products_image_4
 
3,068hrs, complete with 5 buckets. Lovely, tidy machine, with full vandal guard kit for cab glass and original operators book. Arm is piped up for breaker, borer etc. Quick hitch style bucket attachment.

2007 Volvo EC15B XR 1.5T Excavator

products_image_2products_image_3products_image_4
 
1,794 hrs. Complete with 3 buckets (38" grading, 23" and 11" digging). With Mitsubishi L3E engine. Arm is piped for a breaker, borer etc. Nice, tidy machine.
£7,250+VAT
 

Indespension 7ftx16ft Challenger Tilt-Bed

products_image_2products_image_3products_image_4
 
Hydraulic tilt-bed trailer. Gross weight: 3,200kg Complete with winch, spare wheel & integral drop down ramp. Seen some action, but loads more to give.

MF500 Series Pick Up Hitch

products_image_2products_image_3products_image_4
 
Complete unit, with all bolts and fixings and drawbar etc. Later rod-type pick up bars. Recently removed from an MF590, but will fit all 500 series and some 100 series tractors.
£560+VAT

Small Single-Horn Anvil

products_image_2products_image_3
 
24cm (9-1/2") tall, 50cm (20") long single-horn anvil. Great condition, with hardy and pritchel holes.

Agmeier Continental Belton Post Hole Auger

products_image_2products_image_3products_image_4
 
Complete with 9" auger and operators manual (the ops manual isn't 9", that's A4, the auger is 9"). Looks to have done little work, and what work it did was boring. Get it? Boring. Like, uninteresting, but like boring a hole at the same time? Oh, forget it...
£425+VAT
 

Danuser Digger F-8 Post Hole Auger

products_image_2
 
Built in Missouri, USA. Good working order, with PTO shaft and 12" auger bit.
£495+VAT

Bomford B458 Hedgecutter

products_image_2products_image_3products_image_4
 
Good order, complete with control box. Fitted with Trim-Master 1.2mtr flail head.
£2,950+VAT

McConnel Power Arm 470E Hedgecutter

products_image_2products_image_3products_image_4
 
3 point linkage mounted, with control box. 1.2mtr cutting flail head.
£2,700+VAT

Front Snow Blade & Bracket

products_image_2products_image_3
 
4'6" snow blade, with universal mounting bracket. Hydraulically adjustable. Ideal for compact tractor.
£350+VAT
 

Twose 402 Yard Scraper

products_image_2products_image_3products_image_4
 
Complete with quick detach A-frame.
£375+VAT

Bentall Linkage Mounted Cement Mixer

products_image_2products_image_3
 
3 point linkage, tractor mounted. In one ownership from new.
£150+VAT

Tractor Mounted PTO Cement Mixer

products_image_2products_image_3products_image_4
 
Unknown make/model. Good, working order. Complete with shaft.
£360+VAT

Bamlett Linkage Mounted Cement Mixer

products_image_2products_image_3products_image_4
 
3 point linkage tractor mounted cement mixer by A C Bamlett Ltd. Super condition.
£495+VAT
 

Teagle ‘Tipmix’ Cement Mixer

products_image_2products_image_3products_image_4
 
3 point linkage mounted cement mixer. Good condition.
£350+VAT

Markham 3-4 Ton Tipping Trailer

products_image_2products_image_3products_image_4
 
Martin Markham double drop-side trailer, ideal for stable yard etc. Complete with bale extension. Floor to rear of trailer needs attention.
£695+VAT

Trailer Hire Available

products_image_2products_image_3products_image_4
 
We have trailers for hire. For example we have an Ifor Williams LM146 with ramps and sides. Only £50.00 + VAT per day. Or for something smaller we have the Ifor Williams P6E 500Kg unbraked car trailer. Only £25.00 + VAT per day. All trailers are available for longer periods, please call for rates.

Ifor Williams Mesh Sides For P Series Unbraked Trailers

 
Mesh sides for unbraked ramp models available. P6E - £205+VAT P7E - £215+VAT P8E - £260+VAT
 

Ifor Williams P6E 750kg Trailer

 
Complete with ramp. 1.98mtr (length inside bed) 1.21mtr (width inside bed). Max gross weight: 750kg Unladen weight: 197Kg Flotation Tyres: 20.5x8x10
£730+VAT

Ifor Williams P6E 750kg Trailer With Mesh Sides

products_image_2products_image_3
 
**AWAITING STOCK** Complete with ramp. 1.98mtr (length inside bed) 1.21mtr (width inside bed). Max gross weight: 750kg Unladen weight: 217Kg Flotation Tyres: 20.5x8x10
£935+VAT

Ifor Williams P7E 750kg Trailer

products_image_2products_image_3
 
Complete with ramp. 2.21mtr (length inside bed) 1.21mtr (width inside bed). Max gross weight: 750kg Unladen weight: 205Kg Flotation Tyres: 20.5x8x10
£790+VAT

Ifor Williams P7E Trailer With Mesh Sides

products_image_2
 
Complete with ramp. 2.21mtr (length inside bed) 1.21mtr (width inside bed). Max gross weight: 750kg Unladen weight: 235Kg Flotation Tyres: 20.5x8x10
£1,005+VAT
 

Ifor Williams P8E 750kg Trailer

products_image_2products_image_3products_image_4
 
Complete with ramp. 2.51mtr (inside bed) 1.45mtr (inside bed). Max gross weight: 750kg Unladen weight: 228Kg Flotation Tyres: 20.5x8x10
£930+VAT

Ifor Williams P8E Trailer With Mesh Sides

products_image_2products_image_3products_image_4
 
Complete with ramp. 2.51mtr (inside bed) 1.45mtr (inside bed). Max gross weight: 750kg Unladen weight: 265Kg Flotation Tyres: 20.5x8x10
£1,190+VAT

Ifor Williams GD84 1400kg Trailer

products_image_2products_image_3
 
**AWAITING STOCK** Single axle GD84 trailer. 165R13C tyres. Complete with loading ramp and prop stands. 1400kg max. gross weight. 4'1" x 8'2" bed.
£1,485+VAT

Ifor Williams GD84 1400kg Trailer With Mesh Sides

products_image_2products_image_3products_image_4
 
**AWAITING STOCK** 165R13C tyres. Complete with loading ramp and prop stands. 1400kg max. gross weight. 4'1" x 8'2" bed.
£1,780+VAT
 

Ifor Williams GD85 1400kg Trailer

products_image_2products_image_3
 
Single axle GD85 trailer. 165R13C tyres. Complete with loading ramp and prop stands. 1400kg max. gross weight. 5'2" x 8'2" bed.
£1,620+VAT

Ifor Williams LM105 Twin Axle Trailer

products_image_2products_image_3products_image_4
 
Max gross weight 2700kg. Tyres: 195/60R12C. With headboard, tailboard and dropsides. Ramps available separately. Basic flat-bed trailer version also available without sides and tailboard, please ask for details.
£2,275+VAT

Ifor Williams LM126 Trailer

products_image_2products_image_3products_image_4
 
Complete with headboard, drop-sides and tailboard. 12' x 6'6" bed. On 195/60R12C tyres. 3500kg max.gross weight. Ramps available separately. Basic flat-bed trailer version also available without sides and tailboard, please ask for details.
£2,600+VAT

Ifor Williams LM146 Trailer

products_image_2
 
Complete with headboard, drop-sides and tailboard. 14' x 6'6" bed. On 195/60R12C tyres. 3500kg max.gross weight. Ramps available separately (6ft ramps - add £205.00+VAT). Basic flat-bed trailer version also available without sides and tailboard, please ask for details.
£2,710+VAT
 

Ferguson Potato Ridger

products_image_2
 
Ideal project.
£225+VAT

Massey Ferguson 718 Potato Planter

products_image_2products_image_3products_image_4
 
Absolutely stunning original 1950's land driven planter. Complete with i.d plates, instruction plate and changeable gear set for different plant spacings. All the rollers and fingers are sound. Would make a great show piece or working machine.
£995+VAT

Ransomes Simms & Jefferies Horse Plough

products_image_2products_image_3products_image_4
 
RND4 plough with RND119 board. Point missing, but really lovely, straight plough.

Ferguson Single Furrow Plough

products_image_2products_image_3
 
With disc & skim. Ideal for creating furrow for sinking rabbit fencing.
£250+VAT
 

Ransomes FR 2 Furrow Plough

products_image_2products_image_3
 
Built for use with Fordson E27N, so with cast handles. One disc missing.

Ford Ransomes 2 Furrow Plough

products_image_2products_image_3products_image_4
 
Digger bodies. Supplied by Fitts Of Tew.
£295+VAT

Ford-Ransomes 2 Furrow Plough

products_image_2products_image_3products_image_4
 
With discs & cast handles. Made for use with Fordson E27N tractor.
£195+VAT

Ford Ferguson 2 Furrow Plough

products_image_2
 
Good order.
 

Simplicity Regent 18.5Hp Ride On Mower

products_image_2products_image_3products_image_4
 
40" mulching deck. 18.5Hp Briggs & Stratton Intek engine. Hydrostatic transmission. Complete with operator and engine manuals.

Logic Flail Mower For Quad Bike (Petrol)

products_image_2products_image_3
 
£1,250+VAT

Superflex Harrow Sections

products_image_2products_image_3products_image_4
 
**SPECIAL OFFER** New 3'-3" x 7'-6" chain harrow section mat. 1/2" diam. high quality carbon steel, giving extreme strength and resistance to wear. These mats are brand new stock. This low, low price won't last! Priced per mat (usual RRP £203+VAT).
£130+VAT

Oxdale 6ft Folding Mounted Chain Harrow

products_image_2products_image_3
 
Folds to just over 4ft width. Ideal for compact tractors and premises with small entrances. 12mm tine thickness, 5ft 7" deep frame. 3 point linkage mounted.
 

4′ Trailed Chain Harrows

 
4' trailed chain harrow. 5.5' deep, 12mm x 65mm tines. 80 tine points, approx 50Kgs Complete with weights. Other sizes available, please see site for details.
£195+VAT

6′ Trailed Chain Harrows

 
6' trailed chain harrow. 7.5' deep, 12mm x 65mm tines. 140 tine points, approx 75Kgs Other sizes available, please see site for details.
£275+VAT

8′ Trailed Chain Harrows

 
8' trailed chain harrow. 7.5' deep, 12mm x 65mm tines. 200 tine points, approx 100Kgs Other sizes available, please see site for details.
£395+VAT

10′ Trailed Chain Harrows

 
10' trailed chain harrow. 7.5' deep, 12mm x 65mm tines. 240 tine points, approx 125Kgs Other sizes available, please see site for details.
£475+VAT
 

Beaco 4ft Mounted Chain Harrows

 
4' mounted Beaco chain harrows. 6' deep (frame not mat). Full range available, please see our site for details.
£450+VAT

Beaco 6ft Mounted Chain Harrows

products_image_2products_image_3
 
6' mounted Beaco chain harrows. 7'-10" deep (frame not mat). Full range available, please see our site for details.
£650+VAT

Beaco 8ft Mounted Chain Harrows

products_image_2products_image_3
 
8' mounted Beaco chain harrows. 7'-10" deep (frame not mat). Full range available, please see our site for details.
£795+VAT

Beaco 10ft Mounted Chain Harrows

products_image_2products_image_3
 
10' mounted Beaco chain harrows. 7'-10" deep (frame not mat). Full range available, please see our site for details.
£995+VAT
 

Beaco 12ft Mounted Chain Harrows

products_image_2products_image_3
 
12' mounted Beaco chain harrows. 7'-10" deep (frame not mat). Full range available, please see our site for details.
£1,095+VAT

Beaco 16ft Mounted Chain Harrows

products_image_2products_image_3
 
16' mounted Beaco chain harrows. 7'-10" deep (frame not mat). Full range available, please see our site for details.
£1,195+vat

Fleming AR8 Aerator

products_image_2
 
Relieves compaction and promotes healthier root system, giving better quality grass crop. Also improves drainage. 8ft rigid model, with weight carrying rack and chain harrow towing eye. Available for hire at £100+VAT per day.
£1,795+VAT

Fleming Rollers Ready For Immediate Delivery

 
We keep a range of rollers in stock, please ask for details!
 

New Fleming 4ft Ballast Roller

products_image_2products_image_3
 
4ft Fleming ballast roller. Brand new. Ideal for quad bike use. Now with galvanised frame!
£595+VAT

New Fleming 5ft Ballast Roller

 
5ft Fleming ballast roller. Brand new.
£695+VAT

New Fleming 6′ 6″ Ballast Roller

products_image_2
 
6ft 6" Fleming ballast roller. D-Loop hitch, with 3 point linkage mounting on rear for easy transport.
£775+VAT

New Fleming Water Ballast 8′ 30″ Roller

products_image_2products_image_3
 
8' 30" New Fleming Water Ballast Roller. D-Loop hitch, with 3 point linkage mounting on rear for easy transport. Scraper kit available for an extra £100
£995+VAT
 

New Fleming Water Ballast 10′ 30″ Roller

products_image_2
 
10' 30" New Fleming Water Ballast Roller. Scraper kit available for an extra £100
£1,395+VAT

Fleming 3ft Topper

products_image_2
 
£650+VAT

Fleming 4ft Topper

products_image_2
 
Ideal for any Small Tractor.
£750+VAT

Fleming 5ft Topper

products_image_2
 
Ideal for MF35 or Dexta. Now with galvanized skids.
£850+VAT
 

Fleming 6ft Topper

products_image_2
 
£950+VAT

Kidd 240 8ft Topper

products_image_2products_image_3products_image_4
 
Now in stock! Timed drive, shear bolt protected overlapping blades. Special parabolic skids minimise field marking. No top link required.
£1,875+VAT

Fleming 9ft Topper

products_image_2products_image_3
 
£1,875+VAT

Fleming/Sitrex 120 Finishing Mower

products_image_2
 
4ft finishing mower.
£1,145+VAT
 

Fleming/Sitrex 150 Finishing Mower

products_image_2
 
5ft finishing mower.
£1,245+VAT

Fleming/Sitrex 180 Finishing Mower

products_image_2
 
6ft finishing mower, suitable for MF35 etc.
£1,450+VAT

Fleming/Sitrex 230 Finishing Mower

products_image_2
 
8ft 5 blade finishing mower suitable for 40hp+ tractors.
£1,845+VAT

Major Swift MJ70-190 Roller Mower

products_image_2products_image_3
 
6'3"(1.90 mtr) working width, for 25-50 Hp tractor. 3 rotors, 6 blades. 445kg. Adjustable cutting height, from 10mm to 150mm. 3 point linkage mounted. Gear driven.
£4,350+VAT
 

Major Swift MJ70-240 Roller Mower

products_image_2products_image_3products_image_4
 
8ft (2.4mtr) working width, for 30-70 Hp tractor. 4 rotors, 8 blades. 529kg. Adjustable cutting height, from 10mm to 150mm. 3 point linkage mounted. Gear driven.
£4,950+VAT

Major MJ22-140 Flail Mower

products_image_2products_image_3products_image_4
 
A sturdy and compact shredder/flail mower. 3 point linkage mounted. 1.3mtr (4' 4") working width. Suitable for 30Hp+ tractors. 3 belts, 327Kg overall weight. 20 hammers flails.
£2,650+VAT

Major MJ22-170 Flail Mower With Hydraulic Side Shift

products_image_2products_image_3products_image_4
 
1.7mtr cut. Sturdy & compact, 3-point linkage mounted shredder/flail mower. Machine is offset by hydraulic control.
£3,750+VAT

Fleming TR1 Tipping Trailer

products_image_2products_image_3products_image_4
 
6ft 3" x 4ft , 1.5 Ton tipping trailer. With drop-sides. Sides are removable.
£1,670+VAT
 

Fleming TR2 Tipping Trailer

products_image_2products_image_3products_image_4
 
8ft 6" x 4ft 7", 2 Ton tipping trailer. With drop-sides.
£1,895+VAT

Fleming TR4 Tipping Trailer

products_image_2products_image_3
 
10ft x 6ft 6" 4 ton tipping trailer.
£2,450+VAT

Fleming TR4 Tipping Trailer With Mesh Sides

products_image_2products_image_3products_image_4
 
10ft x 6ft 6" 4 ton tipping trailer. Complete with mesh sides.
£2,950+VAT

Fleming TR6 Tipping Trailer

products_image_2products_image_3
 
12ft x 7ft 6 ton tipping trailer.
£3,200+VAT
 

Fleming TR6 Tipping Trailer With Mesh Sides

products_image_2products_image_3products_image_4
 
12ft x 7ft 6 Ton tipping trailer. Complete with mesh sides.
£3,800+VAT

Fleming TR8 Tipping Trailer

products_image_2products_image_3products_image_4
 
General purpose, 8 ton  capacity. Hydraulic double braked, spring suspension tandem axles. 13ft x 7ft.
£4,950+VAT

Hycrack HC1X Tractor Mounted P.T.O Log Splitter

products_image_2products_image_3products_image_4
 
HC1X model, P.T.O driven, tractor mounted log splitter. Ideal for compact tractor. 20-25 Hp for optimal performance. Ideal for logs up to 60cm (24") long by 75cm (30") diameter. Complete with P.T.O shaft.
£875+VAT

Hycrack HC1XW Tractor Mounted P.T.O Log Splitter

products_image_2products_image_3products_image_4
 
HC1XW model, P.T.O driven, tractor mounted log splitter with extra wide platform. Ideal for compact tractor. 20-25 Hp for optimal performance. Ideal for logs up to 60cm (24") long by 75cm (30") diameter. Complete with P.T.O shaft.
£930+VAT
 

7ft 6 Muck Grab

products_image_2products_image_3products_image_4
 
Possibly Strimec, with Manitou brackets. 10 x 1mtr tines. Very little use from new.
£1,200+VAT

Browns Bale Handler

products_image_2products_image_3products_image_4
 
Fitted with Quicke brackets. Early type with non-removable tine rollers.
£525+VAT

Perry Bale Grab

products_image_2products_image_3products_image_4
 
Complete and very tidy for age.
£150+VAT

Heavy Duty Flat 8 Grab

products_image_2products_image_3
 
Unknown make, but very well built.
£225+VAT
 

Browns Flat 8 Bale Grab

products_image_2products_image_3
 
With Quicke brackets and pipework. Very tidy, used this season.
£375+VAT

Browns Flat 8 Grab

products_image_2products_image_3products_image_4
 
Complete with pipework and adjustable brackets (will fit any loader with pin attachments).
£295+VAT

Flat-8 Bale Grab

products_image_2products_image_3
 
Complete with brackets and pipework. Unknown make, looks to be on JCB Toolcarrier brackets (pin hole diameter = 35mm / underside of top hook to pin hole centre = 520mm).
£260+VAT

Meijer-Holland Flat-8 Bale Grab

products_image_2products_image_3
 
Light frame, ideal for smaller loader tractor. Only needs single acting supply, as return is operated by spring loading.
£225+VAT
 

Cook Flat-8 Bale Sledge

products_image_2products_image_3
 
Complete, with draw-bar to fit baler.
£450+VAT

Lister Cockshutt 2 Furrow Plough

 
For restoration.
£150+VAT

Oxdale E400 Electric Log Splitter

 
The electric motor drives a hydraulic pump. 10 ton splitting force. The log splitter has been designed to plug into single phase electricity supply and can be used with extension leads. It can be used inside or outside and is shower proof. The E300 can take logs up to 18” high and is not restricted to the diameter of logs it can take.
£885+VAT

Oxdale PTO Saw Bench

 
Saw bench comes equipped with PTO shaft and 700mm tungsten tipped blade. It is capable of cutting through logs up to 12” in diameter. Blade is balanced for smooth running and efficient cutting. Safety stop lever. Full guarding for effective and safe operation. 540rpm.
£1,095+VAT
 

Oxdale PTO400 PTO Driven Log Splitter

 
Tractor mounted, PTO driven log splitter. 10 ton splitting force. Suitable for all tractors with Cat. 1 and Cat. 2 linkages, including low horsepower compact tractors and large high horsepower tractors. Minimum Hp: 10 Max. PTO Speed: 540rpm. Capable of splitting logs up to 18” high and is not limited to the width of logs it can split.
£820+VAT

Oxdale TM400 Hydraulic Log Splitter

 
Tractor mounted, hydraulic log splitter. 10 ton splitting force. Suitable for all tractors with Cat. 1 and Cat. 2 linkages, including low horsepower compact tractors and large high horsepower tractors. Minimum Hp: 10 Required Flow: 1-40 l/min. Capable of splitting logs up to 18” high and is not limited to the width of logs it can split.
£480+VAT

Ringrose MkII P.T.O Driven Generator

products_image_2products_image_3products_image_4
 
20KVA, 3 phase P.T.O driven generator. Complete with electrical change over switch and P.T.O shaft. Ideal standby machine. Tested (with a test light, not at full load) and generating well.
£750+VAT

Browns Bale Transporter

products_image_2products_image_3products_image_4
 
1990. A wide wheelbase enables it to be operated by tractors of a smaller horespower. Steel box section used throughout, which gives a high strength to low weight ratio. Designed to carry 72 conventional bales in layers of eight, stacked nine high - 10 big bales 700mm high or 8 big bales 800mm high.
£1,250+VAT
 

Kverneland UN7515 Bale Wrapper

products_image_2products_image_3products_image_4
 
Very tidy, with 7575 control unit. Supplied with brand new set of belts (not fitted). Used this season, in great order, sold due to retirement. Still has a roll and half of 750mm green wrap on board.
£2,950+VAT

PZ Haybob

products_image_2products_image_3
 
New tines & springs fitted. Gate is a bit tatty. Cheap and cheerful machine.
£495+VAT

PZ Zweegers Haybob

products_image_2products_image_3products_image_4
 
Spreads, turns, rows up. The little machine that does it all. Every home should have one.
£750+VAT

JF-Stoll Z555 Hydro Hay Tedder

products_image_2products_image_3products_image_4
 
Hydraulic folding, 4-rotor, 5.4 mtr hay tedder. Minimum 30Hp tractor required. 505kg. Looks to have had very little use. Nice condition all round.
£2,450+VAT
 

New Holland 276 Super Hayliner

products_image_2products_image_3products_image_4
 
Conventional baler. Tidy machine for its age. Ideal for smallholder etc.
£1,500+VAT

New Holland 286 Super Hayliner Baler

products_image_2products_image_3
 
Dry stored for years. Recently been through our workshop, serviced and tested. Used out in our field, baling a treat!
£1,850+VAT

1984 Marston 9 Ton Tipping Trailer

products_image_2products_image_3products_image_4
 
With brakes and lights. Monoque body.
£2,750+VAT

Fleming TOP9 Inline Topper

products_image_2products_image_3products_image_4
 
9ft cut. 2008 model. Been through our workshop, so fully serviced and had new gearbox fitted. Ready to go!
 

Spearhead 460 Batwing Topper

products_image_2products_image_3
 
4.6mtr (15ft) cutting width. 3 rotors, 25mm-400mm cut adjustment. 70Hp+ tractor requirement.
£3,400+VAT

Ransomes Mk IIM Trailed 3-Gang Mower

products_image_2products_image_3products_image_4
 
Retired, direct from cricket ground where contractors have taken over the work. Good tyres, and good order overall. Ready to go.
£495+VAT

Spearhead Trident 5000 Flail Mower

products_image_2products_image_3products_image_4
 
Model number: 9560354
£4,950+VAT

Wessex 5ft Finishing Mower

products_image_2products_image_3products_image_4
 
915-4 model with mulching deck. Tidy condition and well maintained.
£695+VAT
 

Kleen Cut 5ft Finishing Mower

products_image_2products_image_3
 
3-point linkage mounted, with four wheels. Ideal for compact tractor.
£650+VAT

Sitrex SM-180 Finishing Mower

products_image_2products_image_3
 
6ft cut, 2006 machine. Dry stored with little use. Serviced, ready to go. Just add sunshine (not included).

Sitrex SM-180 6ft Finishing Mower

products_image_2products_image_3
 
Tidy and ready to go. Fitted with anti-scalp front roller.
£775+VAT

Caroni TC910 7ft6 Finishing Mower

products_image_2products_image_3products_image_4
 
5-blade machine. Supplied new by us in 1999 and had very little use. Very well looked after.
£995+VAT
 

Sitrex 8ft Finishing Mower

products_image_2products_image_3
 
Ex-demo machine, used by us. 2009 machine, but relatively 'as new' as you can see in the pictures.
£1,495+VAT

Single Furrow Plough

products_image_2products_image_3
 
Ideal for fencing (creating a furrow to bury rabbit netting).
£225+VAT

Sellar & Son Single Furrow Plough

products_image_2products_image_3products_image_4
 
Complete with depth wheel. Popular for fencing jobs, creating a furrow to bury rabbit netting.
£175+VAT

Ferguson Single Furrow Plough

products_image_2products_image_3
 
With disc but no skim.
£195+VAT
 

Ferguson 2 Furrow Plough

products_image_2products_image_3
 
Complete with discs, ideal project.
£195+VAT

International B43 Match Plough

products_image_2products_image_3products_image_4
 
2 furrow. Complete, with polished boards, discs & skims. Depth wheel and left-hand disc. Excellent little plough, ready to go straight in to a match.
£495+VAT

Bamford 2 Furrow Plough

products_image_2products_image_3
 
Type 622 with discs & skims. Good metalwork, rear furrow wheel and depth wheel.
£750+VAT

David Brown 2 Furrow Plough

products_image_2products_image_3
 
Complete with depth wheel.
£295+VAT
 

Lemken DL090 2 Furrow Reversible Plough

products_image_2products_image_3products_image_4
 
Complete with skims. Good metal work. LWS bodies.
£895+VAT

International 3 Furrow Plough

products_image_2products_image_3products_image_4
 
With depth wheel & one disc.
£250+VAT

David Brown CM3 3 Furrow Plough

products_image_2products_image_3products_image_4
 
Complete with discs. Good boards, two points missing. Straight, tidy little plough.
£475+VAT

Ferguson 3 Furrow Plough

products_image_2products_image_3products_image_4
 
Complete with discs (skim holders, but no skims). Lovely plough.
 

Ferguson 3 Furrow Plough

products_image_2products_image_3products_image_4
 
Ideal for restoration. With width control. 2 discs missing.
£200+VAT

Ferguson 3 Furrow Plough

products_image_2products_image_3products_image_4
 
Ideal for restoration. With width control. Two discs missing.
£200+VAT

Ransomes Single Furrow Trailer Plough

products_image_2products_image_3
 
Complete, but in need of restoration.
£195+VAT

Ransomes RSLD Trailer Plough

products_image_2products_image_3products_image_4
 
Narrow bodies. For restoration. Wheel is missing.
 

Sub Soiler

products_image_2products_image_3
 
Single leg ripper/sub soiler. Simple as that, really.
£250+VAT

Browns Single Leg Subsoiler

products_image_2products_image_3products_image_4
 
This implement has seen very little use from new. Very tidy!
£450+VAT

J W Blench Sub Soiler

products_image_2products_image_3products_image_4
 
Single leg sub-soiler. Good condition.
£595+VAT

Ferguson Spring Tine Cultivator

products_image_2products_image_3products_image_4
 
Needs new points. Ideal restoration project.
£160+VAT
 

Ferguson Cultivator

products_image_2products_image_3
 
Adjustable tine type. 9 tines.
£195+VAT

Ransomes No.9 RSLM Trailer Plough

products_image_2products_image_3products_image_4
 
3 furrow.  Would make lovely, original plough. No discs, but other than that complete.
£295+VAT

Ransomes No.3 Motrac Trailer Plough

products_image_2products_image_3products_image_4
 
Fitted with YL165 bodies. Complete with discs & skims. Boards in excellent condition. Last used 20 years ago, greased and dry stored.
£475+VAT

Ransomes 9 Tine Cultivator

products_image_2products_image_3
 
Trailed, 7ft wide. Ideal for vintage working area etc.
£195+VAT
 

Ferguson 9 Tine Cultivator

products_image_2products_image_3products_image_4
 
Ideal for restoration.
£150+VAT

Ferguson 9 Tine Cultivator

products_image_2products_image_3
 
Good order. 9 tines. It's a cultivator. It was made by Ferguson. What more can I tell you?

10ft Spring Tine Cultivator

products_image_2products_image_3
 
With end link mount. Another cultivator. To add to our extensive and some would say expansive, (although I would say exhaustive) cultivator range.
£195+VAT

Kongskilde Triple K Cultivator

products_image_2products_image_3products_image_4
 
3mtr spring tine cultivator. A true classic. Complete with depth wheels & quick-hitch tool bar. Tidy condition.
£395+VAT
 

Browns Panbuster Cultivator

products_image_2products_image_3
 
Heavy duty 7 tine panbuster. Couple of points required, then good to go!
£275+VAT

Heavy Duty Cultivator

products_image_2products_image_3
 
11ft width, 14 tine. Cheap and cheerful.
£225+VAT

Menage Land Leveller

products_image_2products_image_3products_image_4
 
3.5mtr rigid tine leveller. Ideal for large gallop etc. With adjustable level board on front. Tine and crumbler roller on back.
£575+VAT

Ferguson Potato Ridger

products_image_2products_image_3products_image_4
 
In good order. One point is missing a chunk.
£200+VAT
 

Johnson’s Elevator-Digger

products_image_2products_image_3products_image_4
 
Single row potato lifter. Looks to have done little work. Good all round condition.
£650+VAT

Port Agric Gladiator 125 Rotavator

products_image_2products_image_3products_image_4
 
4ft compact tractor rotavator. Ideal for allotments etc. Used but good.
£665+VAT

Howard Selectatilth 50″ Rotavator

products_image_2products_image_3products_image_4
 
Complete with original PTO shaft. Tidy, working with good blades.
£650+VAT

Massey Ferguson 174 Disc Harrow

products_image_2products_image_3products_image_4
 
Ideal for restoration project. Discs are in good order.
£275+VAT
 

Ferguson Logging Saw Bench

products_image_2products_image_3
 
Complete. Ideal for work or show.
£350+VAT

Ferguson TEA20

products_image_2products_image_3products_image_4
 
Petrol tractor, fitted with howard reduction gear box, fitted with lights, road registered with v5c, 12 volt system.

Fleming 5ft Grader

products_image_2
 
5ft Grader from Fleming. Brand new. Other size available, please see our site for details.
£350+VAT

Fleming 8ft Grader

 
8ft Grader from Fleming. Brand new. Other size available. please see our site for details.
£495+VAT
 

Fleming 5ft Topper (New)

products_image_2
 

Fleming 9ft Topper (New)

products_image_2products_image_3
 

Fleming Haybob

products_image_2products_image_3products_image_4
 
The most complete universal Haymaker. Excellent job in spreading, tedding or windrowing. 3mtr working width. Adjustable deflectors allow for the correct working conditions. 20Hp +
£2,200+VAT

Mesko-Rol Z175-1 Drum Mower

products_image_2products_image_3products_image_4
 
1.65mtr working width. Over-run drive line. Minimum 35Hp required. The drums are equipped with three cutting knives each, for a thorough and even cut.
£1,950+VAT
 

Fleming Mini Muck Spreader

products_image_2products_image_3
 
20HP Drum thickness - 3MM Overall length - 1.5M Width-2.1M Loading height - 1M Unladen weight - 200KG PTO speed - 540RPM
£750+VAT

Fleming MS450 Muck Spreader

products_image_2products_image_3
 
**AWAITING STOCK** 4 cu. yd. capacity. Built for use with 30 – 40 horse power tractors. Fitted with 3mm reinforced body with large easy to use wash-out bung. Heavy duty balanced rotor fitted with 10mm flails and spreader plates.
£2,950+VAT

Fleming Sicma TSZLL130 1.3mtr Rotorvator

products_image_2products_image_3
 
Mounted rotorvator, ideal for 20-45Hp tractor. 36 Blades.
£1,450+VAT

International 434 2WD

products_image_2products_image_3products_image_4
 
Starts & runs, but needs tidying. Ideal project tractor.
£1,200+VAT
 

Case I-H 695 Tractor 1990

products_image_2products_image_3products_image_4
 
5,000 hours. New seat and headlight and window fitted. Tidy tractor all round. Road registered with V5C.
£5,500+VAT

Case I-H Super 895 2WD 1990 Tractor

products_image_2products_image_3products_image_4
 
7600 hrs. Good tyres. Straight, genuine machine. Good, value for money tractor. Road registered, with V5 document.
£5,750+VAT

Case JX90 4WD 2008

products_image_2products_image_3products_image_4
 
1,167 hrs, with air con, rear spools and 540 or 1000 speed PTO. Very tidy and mechanically sound.
£16,950+VAT

Fordson Super Major

products_image_2products_image_3
 
Live Drive model with Mini Mech pump. Reg No ATE 203A. Good, tidy, original tractor.
£3,250+VAT
 

Ford 3000 Force

products_image_2products_image_3products_image_4
 
Very nice, original tractor. Starts & Runs well. New lights fitted, but needs wiring up. Complete with drawbar. Ideal small tractor for yard work.
£3,950+VAT

Ford 4000

products_image_2products_image_3products_image_4
 
3 cylinder diesel, 60Hp with power steering. Drawbar and linkage all sound. Good starter, new dynamo and seat recently fitted.
£3,850+VAT

Ford 4600 2WD

products_image_2products_image_3products_image_4
 
60Hp with bubble cab. 3 cylinder, power steering, P.U.H & swinging drawbar. Road registered with V5C document.

1990 Ford 3910 II Rice Special 4WD

products_image_2products_image_3products_image_4
 
50Hp, with ROPS canopy. 2,369hrs, this tractor is a very genuine machine. Looks and sounds lovely. 4WD tractors of this size are increasingly difficult to find. Ideal little workhorse, or would tidy up nicely as a show-piece. Not road registered, no V5C.
£6,400+VAT
 

Ford 7610 Series II 4WD 1986

products_image_2products_image_3products_image_4
 
**CURRENTLY ON HIRE** 100Hp 7610 with Super-Q cab. New front tyres and mudguards fitted. New seat. Fully serviced and ready to go. With V5C & taxed. Tidy machine.
£10,500+VAT

Fordson Standard Narrow Wing

products_image_2products_image_3products_image_4
 
Hi-ratio gear version, giving 18mph top speed. Enough to be at the front of the pack on your local road run! Not currently road registered, no V5.
£2,400 NO VAT

JCB 520-50 2004

products_image_2products_image_3products_image_4
 
Complete with forks. JCB 520-50 Telehandler, 2004. 3700 hrs. 2000kg lift capacity with 5mtr reach.
£16,950+VAT

JCB 8008 Mini-Digger With Buckets

products_image_2products_image_3products_image_4
 
2010 JCB 8008 mini digger. Complete with 2 buckets.
 

Kidd PTO Sawbench

products_image_2products_image_3products_image_4
 
3 point linkage mounted, with rolling log carrier & ripping guide. Blade looks to be good, and overall tidy condition.
£695+VAT

McConnel Saw Bench

products_image_2products_image_3products_image_4
 
V-belt type with 3-point linkage mounting. Rolling table, very clean and genuine.
£895+VAT

McConnel PTO Saw Bench

products_image_2products_image_3products_image_4
 
Designed specifically for use with the Nuffield Universal tractor, and still has the plate that states this (although will work on any tractor, obviously). Overall good order, needs new belt.
£475+VAT

McConnel Diesel Engine Driven Saw Bench

products_image_2products_image_3products_image_4
 
Lister 14.3Hp engine, handle start. With drawbar and prop-stands.
£695+VAT
 

Chard Saw Bench

products_image_2products_image_3
 
Pulley type, cast frame with 30" blade. With guide. Fully adjustable.
£175+VAT

Ford 3930 2WD

products_image_2products_image_3products_image_4
 
L-reg, synchro shuttle. On grass tyres, 4,500 hours. P.U.H. Starts and runs well.
£5,750+VAT

Ford 3930 2WD 1990

products_image_2products_image_3products_image_4
 
Synchro shuttle, 1,172hrs. Heavy duty back end, with heavier arms. Very tidy. Road registered with V5C document.
£8,950+VAT

New Holland TC21D Compact

products_image_2products_image_3products_image_4
 
18Hp, 3 cylinder compact, manual transmission. Approx 2000 model. Originally 4WD, but front drive has been disconnected and removed (probably due to fault) so is not present or part of the sale. Power steering, 3-point linkage & P.T.O. Tipping pipe and turf tyres on rear.
£2,600+VAT
 

New Holland TN55 2WD Compact

products_image_2products_image_3products_image_4
 
50Hp 2002 compact tractor. Although classed as a compact, it is at the larger end of this range. 2,600hrs, with hydrostatic power steering. Mechanical shuttle gears (8 forward, 8 reverse). Complete with ROPS. Not road registered, no V5C.
£6,250+VAT

John Deere 2320 HST Compact Tractor

products_image_2products_image_3products_image_4
 
4WD, 24Hp, hydrostatic drive with turf tyres and cab. Only 572 hours, road registered on 60 plate (2010) with V5C document. Been used for estate maintenance & salt spreading. Lovely little compact, starts and runs well. Front snow blade and bracket available separately and not included in price (see listing under 'Used Machinery')
£6,750+VAT

John Deere 6200SE 4WD

products_image_2products_image_3products_image_4
 
1997, P-reg with V5C document. Basic version with no air-con, smaller capacity hydraulic pump, no integral cab lights etc. 16-speed Power Reverser transmission. Narrow wheels. Excellent, tidy, genuine tractor. 5,770 hours, great inside and out. Ideal stock-mans tractor (or very upmarket scraper tractor).
£10,950+VAT

John Deere 6200 Tractor 4WD

products_image_2products_image_3products_image_4
 
1995, 6,631hrs, with Powrquad transmission and air-con. Integral cab lights, hi-capacity hydraulic pump. Tidy overall and mechanically sound. Road registered with V5C document.
£12,500+VAT
 

John Deere 6010

products_image_2products_image_3products_image_4
 
4WD, on turf tyres.
£12,000+VAT

John Deere 6010

products_image_2products_image_3products_image_4
 
4WD on Goodyear Ag tyres (90%)
£12,750+VAT

John Deere 6010 Powerquad

products_image_2products_image_3products_image_4
 
4WD, on turf tyres with snow plough.
£12,000+VAT

Leyland 245 2WD Tractor

products_image_2products_image_3products_image_4
 
Cab, power-steering and road registered, with V5C document. Fitted with the same Perkins engine as the MF135, so all the power and reliability of its red counterpart, but with a fraction of the price! All cab glass in good order. Very good, sound tractor.
£3,250+VAT
 

Marshall 302 Tractor

products_image_2products_image_3products_image_4
 
1984 (ish) 30Hp tractor on grass tyres. Built in Turkey by BMC, under licence from Leyland, the Marshall 302 superceded the Leyland 302 (effectively it's the same tractor). Starts and runs well. Ideal paddock tractor or would make a tidy basis for a preservation project.
£3,400+VAT

Ferguson TED20 Tractor

products_image_2products_image_3products_image_4
 
Petrol/TVO with 12 volt system. Starts & runs well. Just retired after many years of sterling service, cutting cricket out-fields. Ideal project tractor.
£950+VAT

Ferguson TEF20 Diesel

products_image_2products_image_3products_image_4
 
Direct from one owner family from new! Very tidy, original tractor (under the paint). Yes, it's red. Yes, it should be grey.
£1,450+VAT

Massey Ferguson 35 3 Cylinder

products_image_2products_image_3products_image_4
 
Barn stored for the past 15 years. We fitted a new battery and away she went! Ideal project, sold as you see it.
£2,200+VAT
 

Massey Ferguson 35 3 Cylinder

products_image_2products_image_3products_image_4
 
Very tidy, genuine tractor. Starts and runs really well, and has custom paint job (it's been hand-painted, and what's more custom than that?) Sekura safety frame, swinging draw bar. New water pump fitted. No V5 document.

Massey Ferguson 35 3 Cylinder

products_image_2products_image_3products_image_4
 
Good, tidy tractor. Resprayed, and looks to have had engine overhaul in recent past. Runs well.
£4,250+VAT

Massey Ferguson 35X Tractor

products_image_2products_image_3products_image_4
 
Very genuine and original tractor, with original handbook & V5C reg. document. With T-bar & P.U.H. A rare opportunity to find a nice original tractor.
£5,400+VAT

Ferguson 35 4 Cylinder

products_image_2products_image_3products_image_4
 
Selling on behalf of our customer, who recently finished the restoration of this tractor., Nice, tidy machine, starts and runs well. Live PTO & hydraulics. Road registered with V5C document.
£5,500 NO VAT
 

Massey Ferguson 135 2WD

products_image_2products_image_3products_image_4
 
Swinging drawbar, Perkins 3 cylinder diesel. Tidy machine.
£3,950+VAT

Massey Ferguson 135

products_image_2products_image_3products_image_4
 
Only 3,500 hours on clock, nice tidy machine.Good tinwork, straight axle model. Swinging drawbar, G-reg with V5C.
£4,650+VAT

Massey Ferguson 135 1970

products_image_2products_image_3products_image_4
 
Straight axle version, H-reg. 100% genuine and original, never been re-painted. Lovely tinwork all round, even the lights all work! All original linkage and the levelling box is still working as it should. Nice clutch & brakes. Appears to be on its original rear tyres (Goodyear's), but they are looking worn (then again, I will be too when I get to 45). Drives beautifully. A real sweet tractor, and wants to be left as it is not restored.
£5,250+VAT

Massey Ferguson 135

products_image_2products_image_3products_image_4
 
With power steering, P.U.H, roll bar & front weight carrier frame. Nice original machine, showing 3,750 hours. Road registered with V5C document.
£4,250+VAT
 

Massey Ferguson 135 With Cab

products_image_2products_image_3products_image_4
 
Lambourn safety cab (no doors). Very tidy, genuine tractor. 3-point linkage & swinging drawbar. Ideal paddock tractor. Recently serviced in our workshop. Road registered with V5C document.
£4,250+VAT

Massey Ferguson 230 With Loader

products_image_2products_image_3products_image_4
 
1984 with 1,800 hrs. Very straight and tidy. Fitted with Faucheux F5 loader and fork. New rear tyres recently fitted. Roll bar & swinging drawbar. Super machine, ideal for stable yard or small holding etc. Fully serviced and ready to work.
£7,250+VAT

Massey Ferguson 240

products_image_2products_image_3products_image_4
 
1980, 2 owners from new, with only 2700 hours. Sympathetically restored, fitted with CabCraft cab. Show winner. Ready for work or show. Road registered with V5C.

Massey Ferguson 20B 1988

products_image_2products_image_3products_image_4
 
With grassland tyres, P.U.H & power steering. Nice cab. This is basically an MF240 tractor with yellow paintwork, being ex-council. Road registered, with V5 document.
£6,250+VAT
 

Cosmo 1.5mtr Bully Tiller Rotorvator

products_image_2products_image_3products_image_4
 
Lightweight Bully Tiller UL-60. Ideal for compact/hobby use. 540rpm drive. 1.5mtr (60") working width.
£1,450+VAT

Fleming Sicma TSST180 1.8mtr Rotorvator

products_image_2products_image_3
 
6ft heavy-duty horticultural model. Heavy duty driveshaft with slip-clutch mechanism. Cat. 2 linkage. Heavy duty rotors, skids and framework/covers. Complete with parking stand.
£2,495+VAT

New Beaco 4′ Transport Box

products_image_2
 
4ft Beaco transport box. Other size available, please see our site for details.
£325+VAT

New Beaco 5′ Transport Box

products_image_2
 
5ft Beaco transport box. Other size available, please see our site for details.
£350+VAT
 

New Beaco 6′ Transport Box

products_image_2products_image_3
 
£450+VAT

Fleming 4ft Hydraulic Tipping Transport Box

products_image_2
 
127Kg box, with hydraulic tipping function. .34 cu.m capacity. Cat 1 pins. Max Hp required 50. 1260mm wide (4ft).
£595+VAT

Fleming 5ft Hydraulic Tipping Transport Box

products_image_2products_image_3
 
267Kg box, with hydraulic tipping function. .54 cu.m capacity. Cat. 2 pins. Max Hp required 80. 1510mm wide (5ft).
£695+VAT

Fleming 6ft Hydraulic Tipping Transport Box

products_image_2products_image_3
 
296Kg box, with hydraulic tipping function. .66 cu.m capacity. Cat. 2 pins. Max Hp required 100. 1830mm wide (6ft).
£725+VAT
 

Fleming Round Bale Stacker

products_image_2products_image_3
 
Large domed 90mm revolving arms to protect wrap when collecting and stacking.Bull bar, to protect tractor and driver when loading at height. Rollers easily removed to use spikes. All pivots are bushed and fitted with grease points. Supplied without brackets.
£725+VAT

Millmaster Loader

products_image_2products_image_3products_image_4
 
Recently removed from Fordson major, but will fit all models (Major, Power Major & Super Major). No bucket or fork.
£295+VAT

New Fleming Bale Spike

products_image_2
 
3 Point Linkage Bale Spike
£250+VAT

Front Loader Bale Spike

products_image_2products_image_3
 
Fleming front loader mounted bale spike, with Euro brackets. Allows easy transportation of silage, hay or straw round bales. Heavy duty tines for secure and safe transport. This spike works equally well with silage, haylage, hay and straw round bales, wrapped bales or unwrapped round bales.
£395+VAT
 

New Farmpower Post Auger P.T.O Driven With 6″ Auger

 
Supplied as standard with 6" auger bit. 6", 9" and 12" augers are available separately from stock at £135 each + VAT to suit any borer with 50mm shaft.
£550+VAT

New Fleming/Sitrex 300 Fertiliser Spinner

products_image_2
 
Salt kit to suit available at extra £150
£375+VAT

New Fleming/Sitrex 500 Fertiliser Spinner

products_image_2products_image_3
 
Salt kit to suit available at £150 extra.
£395+VAT

Standard Fordson Model N

products_image_2products_image_3products_image_4
 
1940's, owned by Cotswold Vintage Tractor partner Keith Underhill. This was his own, personal, tractor he used for road runs & ploughing etc. Engine & clutch rebuilt by him. Lovely all round machine!
£3,600 NO VAT
 

1942 Standard Fordson Mondel N

products_image_2products_image_3products_image_4
 
Wide wing model. Early restoration from 1970, then used exclusively for ploughing matches until early 1990's. Dry stored since. Goodyear tyres on rear. High top gear. We cleaned up the magneto and away she went!
£2,400 NO VAT

Trailed Disc Harrows

products_image_2products_image_3products_image_4
 
Ideal for vintage working area at shows. Very original condition.
£175+VAT

Nicholsons Type 1C Disc Harrows

products_image_2products_image_3products_image_4
 
Trailed. Old, but will still do a good turn!

Rear Mounted Pallet Forks (New)

products_image_2products_image_3products_image_4
 
3 point linkage mounted pallet forks. Tines are rigid. 41" long (usable fork length) 22" inside-inside fork - 31" outside to outside fork. 1000Kg maximum S.W.L rated lift (although this obviously depends on your hydraulics too!)
£195+VAT
 

Tractor Loader Implement Selection

products_image_2products_image_3
 
We stock a wide range of used loader implements. Buckets, forks, grabs, bale spikes etc. Please call or pop along and view!

Digger Buckets Selection

products_image_2
 
We have a wide selection of digger buckets in stock, to suit JCB etc. Many sizes, please call or pop along and view!

Strickland 7ft Bucket

products_image_2products_image_3
 
As new, with JCB Q-Fit brackets.

Oil Tank With Hose

products_image_2
 
Metal bulk fuel tank, complete with delivery hose and nozzle. Approximately 2,500 ltr capacity (550 UK gallons).  
£125+VAT
 

Twose 8ft Water Ballast Roller

products_image_2products_image_3products_image_4
 
New block bearing fitted. With drawbar mounted jack stand. Nice condition.
£795+VAT

6ft Trailed Chain Harrow

products_image_2products_image_3
 
In two sections. Complete with pole. Seen little use from new, virtually no wear on tines.

9ft9 Trailed Chain Harrow

products_image_2
 
In 3 sections with pole, as new condition. Just surface rust.
£325+VAT

Parmiter Zig-Zag Seed Harrows

products_image_2products_image_3products_image_4
 
Set of three harrows with bar.
£160+VAT
 

Solid Ring Chain Harrow

products_image_2products_image_3products_image_4
 
2mtr solid ring chain harrow, looks to be a Zagroda. 3-point linkage mounted, with levelling bars front and rear. This style of harrow is excellent for land levelling and rut/hoof print management in a menage etc.
£395+VAT

Parmiter 10ft Folding Mounted Chain Harrows

products_image_2products_image_3products_image_4
 
Harrow mats in good order.
£495+VAT

Parmiter 6m/20′ Hyrdraulic Folding Chain Harrows

products_image_2
 
Excellent condition
£1,750+VAT

Multel Telescopic Handler Mounted Post Hammer

products_image_2products_image_3products_image_4
 
Currently fitted with Matbro brackets, but could easily be changed to suit any tele-handler. Double spool valve included, to operate weight and tilt the jib sideways. Had little use.
£1,700+VAT
 

Parmiter Post Hammer

products_image_2products_image_3
 
Rope type hammer with manual side shift. Good order.
£995+VAT

Bunded Diesel Tank On Stand

products_image_2products_image_3
 
1000ltr capacity. Outer tank dimensions (mtrs): 2 x 1.2 x 1.1 Stand is 2.5mtrs high. With lockable cabinet containing hose and nozzle.

Small 2 Ton Wheatley Trailer

products_image_2products_image_3
 
Dropside, non-tipping. Ideal for show or smallholding use.  New tyres fitted.
£675+VAT

Parmiter Rear Loader With Fork

products_image_2products_image_3
 
In need of new hydraulic pipe. Ram not checked. Sold as is.
£150+VAT
 

12 Volt Seed Spreader

products_image_2products_image_3products_image_4
 
Complete spreader kit. Includes mountings for ATV/Quad, implement (cultivator etc) and 3 point linkage (in conjunction with quick-attach A-frame, not included). Fully adjustable spreading width between 2 – 24 metres (depending on material type) via in-cab digital control unit. Suitable for spreading: Slug pellets, oil seed rape, grain, grass seed, stubble turnips, clover, mustard, game feed etc
£795+VAT

Vicon PS303 Spinner

products_image_2products_image_3
 
Trailed with engine. Ideal for game feeding etc.
£450+VAT